Established in 1969, Xantech LLC (www.xantech.com) designs and manufactures an extensive range of state of the art A/V distribution and control systems, and component products, many of which have become the de facto industry standards. Since 1969, over two million of these systems have been installed worldwide. The Xantech product line includes LCD Touchpanel Controllers, multi-zone, multi-source audio/video systems, multi-zone, multi-source pre-amplifiers, multi-channel audio amplifiers, infrared receivers, remote control switchers, interface modules, IR connecting blocks, IR emitters, volume controls and IR accessories. These products are the preffered choice of professional installers worldwide.
|
Page 1
( Displaying 10 of 23 Products )
|
|
|
Xantech RC68X IR Remote Programmer
|
|
Xantech RC68X
Infrared remote programmer features more than 14,000 infrared codes
• Contains all the infrared codes necessary to operate all the Xantech infrared controlled components
• Use to program universal learning devices, such as Xantech remotes and keypads
• Infrared control code groups are adjustable within many Xantech components
• Requires two AA batteries (not included)
Weight .5Kg
|
|
Xantech RT8 - Eight-Port Addressable IR Router
|
|
RT8 - Addressable one-in/eight-out Router
The RT8 Router is a ONE-IN/EIGHT-OUT IR switcher. It directs an infrared control signal to any one of 8 output ports or all 8 as a group. It is intended for selective control of up to 8 TV monitors (or any other
A/V product) from control locations using Xantech IR Receivers and /or SmartPads. The "I" and "G" output ports provide the ability to drive LEDs placed at each controlled device location so that you can see which device is being addressed at any given time. The RT8 responds to the Xantech RC68+ (or RC68) commands and is Code Group changeable by the installer.
|
|
Xantech 079144 One-Zone Amplified Connecting Block
|
|
79144 - One Zone Ten Source Amplified Connecting Block
•Emitter port jumpers permit high or low power IR outpout
•High-speed opto-isolator for improved operation
•Parallel emitter ports drive 10 single or 10 dual emitters
•Contains red LED input signal Test-IR
•Requires either the 781ERGPS or 782ERGPS Power Supply
•Dimensions: 6" x 2 1/4" x 15/16" (153mm x 58mm x 24mm)
•Up to nine 790-00's can be connected to the 791-44 for control of up to 100 devices in a single zone
|
|
Xantech 79000 Multiple Emitter Connecting Block
|
|
Xantech 79000 Multiple Emitter Connecting Block
•Emitter expansion block for the 791-44 or 792-10
•Parallel emitter ports drive 10 single or 10 dual emitters
•Contains a series 100-Ohm resistor per emitter port
•Emitter and IN/OUT ports are 3.5 mm mono mini-jacks
•Screw terminals provide for wired input connections
•Requires the 792-10 Power Module or the 791-44 Amplified Connecting Block to drive the 790 block
|
|
Xantech 286D Designer Dual Blink Emitter
|
|
286D
• Two emitters in series with each other and terminated in a single 3.5mm mono mini plug
• Length of wire: 7 feet to junction, 3 feet to each emitter
286D10P - Dual Visible Designer Emitter Ten Pack
Package contains (10) 286D Visible Designer Emitters
|
|
Xantech CB18 - Strip-IR Parallel Connecting Block
|
|
•Easily connects home run wires from multiple IR Receivers to the input
•High current design (12 Amps peak) allows amplifiers rated as high as 500 watts to be used with the CB18
•One-in eight-out or eight-in one-out capability
•Nine four-terminal plug-in connectors on 4-conductor bus
•Screw terminals handle wire sizes from 24 to 12 gauge
•Dimensions: 111/4" x 1 1/4" x 1 1/4" (286mm x 32mm x 32mm)
|
|
Xantech 782ERGPS High Current Power Supply
|
|
782ERGPS - High Current Regulated Power Supply
A high-efficiency power supply specified to provide power to all Xantech IR products. A versatile plug has a locking indentation ring providing a secure connection to all Xantech IR connecting blocks. A small form-factor allows tighter installation and reduces a clumsy rack-installation.
Input Power: 100-240VAC, 15W
Output Power: +12VDC, 1.25A
|
|
Xantech CPL94B RF/IR Coupler
|
|
CPL94B - IR/RF Coupler
•Used to inject the Infrared control signals when used in conjunction with a TV coaxial RF cable.
•Has two "F" type coaxial jacks, one IR receiver 3.5mm mini stereo jack and one 2.1mm power jack.
•IR RCVR jack works with any Xantech IR Receiver having a 3.5mm stereo mini plug.
CPL94B RF/IR COUPLER
•Used to extract the IR control signals when used in conjunction with a TV coaxial RF cable.
|
|
Xantech CPL10 - RF/IR Coupler
|
|
CPL10 - IR/RF Coupler
•Used to extract or inject IR control signals when used in conjunction with a TV coaxial RF cable.
•Has two "F" type coaxial jacks and one IR out (or in) 3.5mm mono mini jack.
|
|
Page 1
( Displaying 10 of 23 Products )
|
|
Search for products that may contain the words:
within
using