The secret to great lighting is being able to control it. Match your activity or mood to your visual environment. Set the lights as you need them and the setting is automatically saved as one of your custom scenes. Retrieve it later at the touch of a button; no individual switches or dimmers to adjust again and again. The possibilities are endless. In your living room, you can pre-set the lighting controls to suit the way that you live “Cinema”, “Homework”, “Entertaining”, “Cleaning”. Then with a hand-held remote control (or even your universal TV remote), you can change the ambience of your room without leaving your chair. You can control all the lights in one room or indeed the whole house from just one button and control natural light with a motorised window solution. You can also link the lighting controls to your security and AV systems.
Control Units have both a maximum power capacity limit per zone and a maximum power capacity limit per unit. Each zone cannot exceed the total Watts listed on the product, and each unit cannot exceed the total Watts outlined for the product. However, the maximum unit capacity can be allocated among each individual zone in the unit. For example, on a 4-zone unit at 230V with a maximum zone capacity of 800W and a maximum unit capacity of 2300W, some zones will not reach the individual zone maximum because the total unit maximum cannot exceed 2300W. Check total unit maximums before ordering
|
Page 5
( Displaying 10 of 102 Products )
|
|
|
Rako RLED45CCI - Wireless 45w constant current dimming module
|
|
The RLED45CC1 is a wireless 45w constant current
dimming LED module, suitable for ceiling or cupboard
mounting.
Designed to fit through a ceiling cut-out of 50mm diameter or greater
the RLED45CC1 is fed from a suitable DC power supply to provide an
adequate forward voltage. The RAPSU48 is recommended.
The unit can also be used for exterior lighting control applications with
the use of a weatherproof IP rated enclosure.
|
|
Rako RSRDMX - 15 channel RAKOM DMX Output Unit
|
|
Wireless 15 channel DMX controller for DMX
controlled LED and other DMX light fixtures.
Designed to be connected to the Rako Rakom wireless network and be
controlled by any Rako wireless transmitter device such as the RCM
wallplates or RA/RTC Bridges. The RSRDMX is addressed as a normal
dimmer channel and automatically assigns the subsequent channels for
DMX use.
DMX connections are available using either screw terminals or an RJ45
socket.
|
|
Rako RAMVR
|
|
The RAMVR is a wireless interface module for third
party presence sensors.
The RAMVR integrates third party presence sensors into a Rako wireless
system where Rako's RAPIR may not be suitable, such as external use. It
also allows sensors using other detection methods such as break-beam or
microwaves to be used.
The RAMVR is mains powered and allows direct connection to sensors that
switch mains power. The module also has isolated volt-free inputs
connections for dry contact or DC logic inputs.
|
|
Rako RMR-VF (RMRVF)
|
|
The RMR-VF is an interface unit to convert volt-free
contact signals into Rako wireless RAKOM messages.
The RMR-VF accepts up to 10 volt-free inputs which can be used to trigger
multiple scenes within a single room or separate commands in different
rooms. Commands can be scenes, fades, levels or multiple actions
depending on the duration of the contact closure.
The RMR-VF can be addressed manually to a single Rako Room and inputs
will trigger basic scenes within that Room. Rasoft Pro is required (with a
suitable programming interface e.g. RABridge) to map commands to
different or multiple rooms and action advanced functions such as Level,
Press and Hold and Trigger on Release.
|
|
Rako RAMPI - USB Wireless and NFC Interface Module
RAMPI
|
|
The RAMPI is a USB programming interface for
Rasoft Pro with NFC (Near Field Communication)
capability.
The RAMPI allows programming of a Rako wireless system from
Rasoft Pro running on either a PC or Mac. The module also has
NFC programming capability for programming Rako's range of NFC
devices.
The module includes a wireless receiver giving message feedback
from other Rako wireless transmitter devices.
Note the RAMPI is not supported by Rasoft Classic.
|
|
Rako WRB100 - RAKOM Radio Signal Repeater
|
|
Used as a wireless repeater the WRB100 receives and repeats Rako
wireless messages thus increasing the range of transmitters. Typically
located between transmitters and repeaters the unit will repeat all
messages from the same Rako 'House' address.
Usually used as a single repeater to avoid messages creating a locked
loop it is possible to configure WRB100 units to repeat messages from
other WRB100 units. Consult Rako's technical team for more
information.
|
|
Rako RSR-DLI
|
|
RSR-DLI
WIRELESS ADDRESSABLE DLI CONTROL MODULE
The RSR-DLI is a wireless control module giving control
of up to 15 addressable channels of DLI controllable
fittings in a single Rako Room.
The RSR-DLI allows a wireless Rako system to have addressable control of
Digital Addressable Light fittings. The module is complete with an 18V DC
power supply that powers the DLI network.
Programming is achieved with Rasoft Pro and allows Auto addressing of
DLI devices. Swap, Move and Group functions allow the user to achieve
a logical arrangement of devices for programming.
|
|
Rako WAPIR - Ceiling Mounted Presence Senor
|
|
A ceiling mount PIR motion
detector with a 360o sensor
pattern.
The unit is ideally suited to
office and residential
applications where automatic
scene selection is required.
MOVEMENT CONTROL
The WAPIR motion detector module allows scenes to be selected
automatically via movement.
In factory default setting, the unit will select scene 1 and off, with a
timeout of 5 minutes. It will also dim lights slightly before going off
entirely, to pre-warn the occupant.
|
|
Rako WAVFR
|
|
A compact interface unit for use
with the Rako Rakom wired
network. The WAVFR allows up
to 10 volt-free contact closures
to interface to the network
which can then trigger lighting
scenes and actions.
Interface unit for connecting volt-free signals from
devices such as security alarms to the Rako Rakom
wired network.
The WAVFR is fitted with a 10 way set of screw terminals for signal
input and an additional 3 way connector for Common inputs. The
WAVFR is configured in Rasoft and signal inputs can trigger lighting
scenes or actions in a similar fashion to button presses on a wallpanel.
Connection to the Rakom wired network can be via the RJ11 lead,
plugging into a RAKLink or RAKStar unit. Alternatively a WPCon or
WPConC unit can be used as a remote plug in connection point or the
network can be punched down on to the daughter board supplied with
the WAVFR.
|
|
Rako WP-CONC (WPCONC)
|
|
The WPCON and WPCON-C
units provide convenient
connection points to the Rakom
wired network for devices such
as DMX, RF, WA and WTC
Bridge modules. They provide a
permanent punch down
connection to the Rakom
network and an RJ11 socket for
plug in connection of the
devices.
IN CONTROL
The WP-Con unit is mounted on a standard 86mm2 plate with 2 screws
fixings to fit a standard 35mm deep single gang UK backbox.
The WPCON-C is mounted in a plastic box with cable strain relief
clamps and is designed for ceiling or cupboard mounted appliances.
|
|
Page 5
( Displaying 10 of 102 Products )
|
|
Search for products that may contain the words:
within
using