Rako are leading the way in providing state of the art digital dimming technology, manufacturing lighting systems that are simple to use, creative, easily installed and cost effective, making the Smart Home dream a reality. Recall a scene, or mood of lighting at the touch of a single button despite controlling multiple circuits and lamp types. Circuits are split to define zones and highlight room features and then programmed to suit the different uses of a space.
control all light fittings, including the dimming of LED's fluorescent lighting and low voltage fittings, saving energy and increasing lamp life as lamps are dimmed.
Advanced programming features allow master off control from any keypad or maybe a button to create a welcome home scene. The addition of a TCM time-clock module provides 'Holiday Mode' security, timed events and astro dawn/dusk programming.
|
Page 3
( Displaying 10 of 94 Products )
|
|
|
Rako RAMPI - USB Wireless and NFC Interface Module
RAMPI
|
|
The RAMPI is a USB programming interface for
Rasoft Pro with NFC (Near Field Communication)
capability.
The RAMPI allows programming of a Rako wireless system from
Rasoft Pro running on either a PC or Mac. The module also has
NFC programming capability for programming Rako's range of NFC
devices.
The module includes a wireless receiver giving message feedback
from other Rako wireless transmitter devices.
Note the RAMPI is not supported by Rasoft Classic.
|
|
Rako WRB100 - RAKOM Radio Signal Repeater
|
|
Used as a wireless repeater the WRB100 receives and repeats Rako
wireless messages thus increasing the range of transmitters. Typically
located between transmitters and repeaters the unit will repeat all
messages from the same Rako 'House' address.
Usually used as a single repeater to avoid messages creating a locked
loop it is possible to configure WRB100 units to repeat messages from
other WRB100 units. Consult Rako's technical team for more
information.
|
|
Rako WAPIR - Ceiling Mounted Presence Senor
|
|
A ceiling mount PIR motion
detector with a 360o sensor
pattern.
The unit is ideally suited to
office and residential
applications where automatic
scene selection is required.
MOVEMENT CONTROL
The WAPIR motion detector module allows scenes to be selected
automatically via movement.
In factory default setting, the unit will select scene 1 and off, with a
timeout of 5 minutes. It will also dim lights slightly before going off
entirely, to pre-warn the occupant.
|
|
Rako WAVFR
|
|
A compact interface unit for use
with the Rako Rakom wired
network. The WAVFR allows up
to 10 volt-free contact closures
to interface to the network
which can then trigger lighting
scenes and actions.
Interface unit for connecting volt-free signals from
devices such as security alarms to the Rako Rakom
wired network.
The WAVFR is fitted with a 10 way set of screw terminals for signal
input and an additional 3 way connector for Common inputs. The
WAVFR is configured in Rasoft and signal inputs can trigger lighting
scenes or actions in a similar fashion to button presses on a wallpanel.
Connection to the Rakom wired network can be via the RJ11 lead,
plugging into a RAKLink or RAKStar unit. Alternatively a WPCon or
WPConC unit can be used as a remote plug in connection point or the
network can be punched down on to the daughter board supplied with
the WAVFR.
|
|
Rako WP-CONC (WPCONC)
|
|
The WPCON and WPCON-C
units provide convenient
connection points to the Rakom
wired network for devices such
as DMX, RF, WA and WTC
Bridge modules. They provide a
permanent punch down
connection to the Rakom
network and an RJ11 socket for
plug in connection of the
devices.
IN CONTROL
The WP-Con unit is mounted on a standard 86mm2 plate with 2 screws
fixings to fit a standard 35mm deep single gang UK backbox.
The WPCON-C is mounted in a plastic box with cable strain relief
clamps and is designed for ceiling or cupboard mounted appliances.
|
|
Rako WP-CON
|
|
Rako Wired Lighting WP-CON - Programming Socket Features
Rako Wired Lighting WP-CON - Programming Socket is used to programme a Rako Wired installation with Rako interface modules; WRE-BRIDGE or PC-BRIDGE.
This unit is also required for RS232-BRIDGE, RF-BRIDGE and DMX-BRIDGE to connect to the RANET CAT5 Bus-Cable
Single gang wired connection to RJ11 socket for interfaces complete with white plastic cover plate.
|
|
Rako WAVMI
|
|
Rako Wired Lighting WAVMI - 5 Way Mains Voltage Input Interface Features:-
WAVMI allows mains voltage signals to be detected by a Rako wired system. So, the Rako system can be made aware that certain circuits are active. This includes inputs from Alarm sensors & PIR modules, central heating controls, fan motors – almost anything.
WAVMI must be connected to A RAKO Wired System. The simplest method is by connecting the RJ11 patch lead from the WAVMI to one of the RJ11 sockets on a system RAK-Link or RAK-Star. The RJ11 patch lead may also be plugged into a WA-Con access point. WAVMI has 5 inputs. Each input is a 4 way terminal block.
|
|
Rako WA-Bridge
|
|
Rako Lighting WA-BRIDGE - Interface between Wired and Wireless Systems with an Ethernet Interface.
Rako Wired Lighting WA-BRIDGE - Ethernet Interface Features:-
Rako Lighting WA-BRIDGE - Interface between Wired and Wireless Systems with an Ethernet Interface. Use with iPhone, iPad, Android remote control applications
One Rako WA-BRIDGE - Ethernet Interface is required for a whole property - Connects via single Cat-5 cable to a WiFi Ethernet Router
|
|
Rako RAK-STAR - Wired Lighting
|
|
Rako Lighting RAK-STAR - CAT-5 16 Way Star Wired Distribution Board. Used in Star Wired Installations
Rako Wired Lighting RAK-STAR - CAT-5 16 Way Star Wired Distribution Board Features
Rako Wired Lighting RAK-STAR - CAT-5 16 Way Star Wired Distribution Board. Supports up to 16 CAT 5 cables in a star wired installations.
Provides 12vDC power for all devices connected to RANET CAT5 bus-cable.
Technical
|
|
Rako RAK-LINK
|
|
Rako Wired Lighting RAK-LINK - RAK Dimmer Interface Module Features:-
Rako Wired Lighting RAK-LINK - RAK Dimmer Interface Module - RANET CAT5 Interface. Controls up to 8 RAK4 Light Dimmers in a Wired Lighting Installation.
Each Rako RAK-LINK - RAK Dimmer Interface Module Supports up to Eight RAK4, RAK4L, RAK4F light dimmers.
Provides 12vDC power for all devices connected to RANET CAT5 bus-cable.
|
|
Page 3
( Displaying 10 of 94 Products )
|
|
Search for products that may contain the words:
within
using