Smooth vinyl precision.
ELAC’s Miracord 50 Turntable is designed to deliver exceptional vinyl transcription, inspired by the iconic Miracord name from the Golden Age of Stereo, when turntables reigned supreme. The Miracord 50 is carefully engineered with a belt-drive motor and die-cast aluminum platter. A precision static balanced, straight-tube tonearm with removable headshell features a factory-mounted MM phono cartridge. Designed with convenience in mind, the Miracord 50 is equipped with a built-in defeatable phono preamplifier, allowing you to add this turntable to virtually any music system.
Anti-resonant Chassis
Superior isolation is achieved with a chassis
designed to minimize the sonic effects of
vibration and feedback. A low-noise DC
servo motor drives a die-cast, high-inertia
aluminum platter with special record mat
via a rubber belt, resulting in stable speed
and minimal wow and flutter.
Precision Tonearm and Cartridge
The tonearm is a static-balance, straighttube
design with precision bearings, builtin
anti-skate adjustment and removable
bayonet-style headshell. A premounted
moving-magnet cartridge takes all the
guesswork out of setup and assures proper
vertical tracking angle, tracking weight and
azimuth adjustment right out of the box.
Built-in Phono Equalizer Amplifier
Unlike most turntables, the Miracord 50
comes complete with a built-in defeatable
phono preamp for correct RIAA equalization.
That means you can add LP playback
without having to add a costly phono
stage to line-level preamps or digital-only
systems. Just plug it in, put on a record
and enjoy rich LP sound
Contemporary Finish
Styled to complement any interior, the
Miracord 50 is available with a silver
chassis and gloss-black plinth. A hinged,
tinted dustcover is included.
Technical Specifications:-
Turntable Section:
•Drive System: Belt drive
•Motor: DC motor
•Selectable Speeds: 33⅓ and 45 rpm
•Motor Servo: Speed rotation and servo system
•Rotation Speed Variation: +/-1%
•Wow and Flutter: 1%
•Signal-to-Noise Ratio: -67 dB or higher (A-weighted) -60 dB or higher (unweighted)
•Platter: Aluminum die-cast
•Platter Diameter: 0 in / 300 mm
Tonearm Section:
•Type: Aluminum tube, static-balanced
•Effective Arm Length: 8 in / 223.6 mm
•Stylus Pressure Range: 0 to 0 g
•Cartridge Weight Range: 5 to 6.0 g
•Effective Arm Mass: 4 g
•Overhang: 6 mm
•Offset Angle: 25 degrees
•Anti-Skating: Adjustment Supported
•Main Bearing: Stainless steel
Cartridge Section:
•Type: Audio-Technica AT91 moving magnet
•Stylus Construction: Bonded diamond
•Mount: Half-inch
•Frequency Response: 20 Hz to 20 kHz
•Channel Separation: > 18 dB
•Channel Balance: 5 dB
•Vertical Tracking: Angle 20 degrees
•Stylus Pressure: 0 g +/-0.5 g
•Cartridge Weight: 0 g +/-0.5 g
•Headshell Weight: 0 g (including screws, nuts and wires)
Phono Equalizer Amplifier:
•Type :Moving magnet (MM)
•Phono Output: 5 mV (1 kHz, 3.54 cm/sec)
•Line Output: 140 mV (-17 dBV)
•Phono/Line: Switchable
•Supported Load Impedance: 47 kΩ
Connector: RCA pin jack including RCA cable accessories
Voltage: 100 to 240 V AC / 50 to 60 Hz
Power Consumption: 1.5 W (less than 0.5 W at standby)
Dimensions: (WXHXD) 5.5 x 16.05 x 14.20
Weight: 12.10 lb